Reasons to Change Door Lock

You can alter your door lock for a variety of reasons, from upgrading the security of your home to redecorating your entryway. It is also possible to change locks if your key gets stuck in the lock or is difficult to turn.

Even DIY beginners can easily change their lock. Get the tools you need to begin.

Remove the old lock

Removal of the lock that was in place before the door is a crucial step prior to installing the new lock. This step is especially important in the event that you suspect someone else has access to your home. It is also a good idea if you have moved into a house that was burglarized, or had a roommate move in. The process is much easier than you might think and can be completed within a few minutes.

Begin by getting rid of the screws that attach the deadbolt faceplate on the door frame. You'll need to take off the screws on both sides of the door to remove the faceplate. This will allow you see the hidden screws and provide you with an understanding of how to continue with the remaining steps.

After removing the old faceplate you must take off the bolt along with the strike plate and strike plate. Use a screwdriver to loosen the bolt and then take it out of the hole in the door lock repair. If the bolt is rusty, you may have to use a chisel smash it out. If you are using a chisel, be cautious not to scratch the door frame.

Before you remove the old lock, be sure that your new doorknob and deadbolt fit into the holes in the door. A lot of hardware stores and big box stores have a wide selection of locks and will assist you in selecting the best one. Ask for help if the lock you bought doesn't fit your door.

Find small depressions or notches in the handle and around the trim while you take off the lock. If you can locate them, insert a straightened safety pin or flat screwdriver into these to loosen the handle and expose the screws beneath.

After you have removed the screw from the handle, you are able to begin removing the knob. To do this, locate the set screw that is located on the base of the knob and loosen it. Next, you will need to remove the knob from the spindle. Finally, carefully remove the spindle from the upvc door locks replacement.

Install the new lock

It's a great idea to change the locks on your doors periodically, especially if you have had a break-in. Changing the lock is a cheap, easy and effective method to ensure that your home is safe. With a screwdriver and a few basic instructions, most people can do it themselves. Based on the situation you may need to learn how to rekey a door lock so that only you own the key.

To start the process, you'll need to buy an additional lock that matches the keyway on your existing lock. You will save money if you change the lock's key yourself. The majority of locksmiths charge a fee to do this. You can purchase a new lock from an hardware store, or on the internet. Standard deadbolts can be fitted to most doors. However, you'll have to measure the door to make sure it will fit.

Most of the time, your new lock will come with the cardboard template that will show the way it will fit on the door. This template can be used to drill the hole. It's much simpler than having to measure each time. If the template doesn't match to the hole you intend to drill then you should take it back to the hardware store and get a different one.

When installing the new lock, remember to put it on the right side of the door. You can check this by inspecting the latch, which ought to be labelled "up" or something similar. Make sure the latch is seated correctly within the latch plate then secure it with the screws supplied.

When replacing knob locks, you should also be aware of its handing. Certain knob locks are right-handed. If you're not careful, you could install the knob on the wrong side of the door, which would prevent you from locking it from either the inside or the outside.

After you've finished, you should test the new lock to ensure it's working. You should be capable of locking the door from both the inside and outside, and unlock it using keys. If you aren't satisfied with the outcome, you can always call a professional locksmith to fix it.

Test the lock

A door lock that will not open is a nuisance however, it could also put your family's safety at risk. It's a good thing that it's simple to fix most issues with door locks by performing some troubleshooting, and lubrication. First, make sure that your key is properly cut and that the lock assembly isn't dirty or loose. If this doesn't solve the problem, you can try applying lubrication to the door lock actuator using powdered graphite or a silicone-based oil.

Make sure that the door lock repair lock switch, wiring harnesses, and the actuator connector are all functioning properly. Consult the wiring diagram or manual to determine the color-coding and function of the wires for each door lock switch. Use a test light or digital meter to determine whether the door lock actuator is receiving power and ground when the switches are activated. If you notice the switches switch on and off with voltage this means that the switches are in good condition and the actuator will require replacement.

If the switch appears to work but the actuator does not move when you turn it, it could be a problem in the cylinder. The actuator cylinder has spring-loaded pins that stop the cylinder from turning until the key is placed in and it pushes the pins up to fit the height of the key in the location. This causes the cylinder eventually to rotate and open the lock body, allowing the latch to open for the handle.

If your door lock actuator is still inoperable, you can remove the switch and wires from the actuator with a small screwdriver to release the locking bolt and remove the plastic cover that holds the electrical connector. Then, disconnect the door actuator from the lock and let it drop down. You should then be able to locate the two bolts of 10mm that keep the actuator in place and then remove them. After the actuator has been removed, you will be able to disconnect the black electrical connector and remove it together with the actuator and lock assembly.

replace lock upvc door the key

If your keyed deadbolt or door knob isn't working, you'll need to rekey it or replace it. It's not too difficult and could save you money. It is best to hire a professional locksmith check the locks for any issues prior to starting. This will give you peace of mind knowing that your home is secure and safe.

Remove the faceplate on the outside of the doorknob/deadbolt. If there are screws that hold the faceplate in place, use a screwdriver and pull it off. Then, you can remove the inside faceplate using a screwdriver that has a flat head. Once you have removed your faceplate, you are able to remove the bolt and a screw from the upvc window lock replacement cylinder.

A locksmith can help determine if the lock you have needs to be replaced or changed. They can also give you guidance on the most effective security measures for your home. They can also make the necessary modifications to your door and frame for a perfect fit. They also offer a guarantee on their work.

If you decide to rekey your lock, you'll have to first buy an additional key for it. It is essential to select a key that fits well inside the lock replacement [Find Out More]. A key that is not properly fitted could cause damage to the mechanism's internal mechanisms and prevent it from functioning. To test the size of a key, insert it into the lock. If it is perfectly with the plug, it's the correct size. If the pins stick up from the top of the plug, then they are too long.

You may want to change the lock on your door for many reasons, including:

If you're moving into an homeowner's house or have lost keys, rekeying your lock could be a more affordable option than replacing it. It's also less expensive than a full replacement. However, there are circumstances where rekeying your existing lock isn't an option. If the lock has been damaged or repeatedly jammed, for instance, lock replacement it may be the right time to replace it.